How to change colors in crochet
The secret to a neat color change is simple: switch to the new color before you finish the last stitch in the old one. Here's how to do it in every kind of project.
The one rule behind every color change
Every crochet stitch ends with a loop on your hook, and that loop sits on top of the next stitch. So if you finish a stitch in blue and then start the next one in yellow, a little blue bump shows at the top of the first yellow stitch. That's the ragged edge most beginners get.
The fix is to change color on the final yarn over of the last stitch in the old color. Work that stitch as usual until there are two loops left on the hook, drop the old yarn, and pull the new color through to finish it. The loop that sits on the next stitch is now the new color, and the line between the two colors comes out clean.
How to change colors, step by step
These steps use single crochet, but the idea is the same for every stitch.
- Work the last stitch in the old color until two loops remain. For single crochet: insert the hook, yarn over and pull up a loop. You have two loops on the hook.
- Drop the old color. Let it hang at the back (or the wrong side) of the work.
- Yarn over with the new color. Leave a tail of about 6 in (15 cm) and hold it against the back of the work with your fingers.
- Pull through both loops. The stitch is finished, and the loop on your hook is the new color.
- Carry on in the new color. Give both tails a gentle tug after the next stitch or two so the first new stitch isn't loose.
For other stitches, the last step changes slightly:
| Stitch | When to switch to the new color |
|---|---|
| Single crochet (sc) | When 2 loops are left on the hook |
| Half double crochet (hdc) | When 3 loops are left: pull the new color through all 3 |
| Double crochet (dc) | When the last 2 loops are left |
| Treble crochet (tr) | When the last 2 loops are left |
| Slip stitch (sl st) | Pull the new color through as the slip stitch itself |
Changing color at the end of a row
For stripes worked in rows, change in the last stitch of the row, using the method above. Then make your turning chain in the new color and work the next row as usual. If the pattern says "fasten off," cut the old color and leave a tail. If the stripes are only two or four rows wide, you don't have to cut the yarn at all: carry the unused color loosely up the side of the work and pick it up when it's needed again. This saves a lot of ends to weave in. Keep the carried strand on the same edge every time, and don't pull it tight, or the side will pucker.
Changing color in the round (and avoiding the jog)
When you work in joined rounds, like the stripes on a hat, change color on the joining slip stitch: insert the hook into the first stitch of the round, drop the old color, and pull the new color through as the slip stitch. Then make the starting chain in the new color.
In a continuous spiral, like most amigurumi, there's no join, so each stripe ends a little higher than it started. That step is called the jog. To soften it:
- Change color as usual at the end of the round.
- Work the first stitch of the new color as a slip stitch instead of a single crochet.
- When you come back around to that slip stitch on the next round, work into it as a normal stitch.
The jog never disappears completely in a spiral, so if you want perfectly straight stripes, work in joined rounds instead.
Changing color in C2C
In corner to corner, each block is made of a chain and three double crochet. Change color on the last yarn over of the previous block, or of the slip stitch that moves you along, so the new block starts with a clean edge. For large areas of color, use a separate small ball or bobbin for each area instead of carrying the yarn across the back, because carried strands in C2C show through the gaps. Our C2C guide covers the full technique, and the graph reading guide shows how to follow the color squares row by row.
Changing color in tapestry crochet
Tapestry crochet uses single crochet with color changes every few stitches. Instead of cutting the yarn, you lay the unused color along the top of the row and work your stitches over it, so it travels hidden inside the stitches until you need it. Change colors with the same last yarn over method. Because the carried yarn adds bulk, tapestry fabric is thick and firm, which suits bags, baskets and potholders.
Cut or carry? A quick guide
| Situation | What to do |
|---|---|
| Stripes in rows, each stripe 2–4 rows | Carry the yarn up the side |
| Wide stripes or a color you won't use again | Cut, leaving a 6 in (15 cm) tail |
| Small motifs, a few stitches apart | Carry inside the stitches (tapestry style) |
| Large color blocks, C2C pictures | Use a separate bobbin for each area |
Dealing with the ends
Each cut color leaves two tails. You can work over them as you go: lay both tails along the top of the next row and crochet over them for a few stitches, then trim. Or weave them in at the end with a tapestry needle, working each tail into stitches of its own color so it doesn't peek through on the right side. Weave in one direction, then turn and go back a short way to lock it.
Common problems and fixes
- A bump of the old color on the new row. You finished the stitch before switching. Switch on the last yarn over instead.
- The first new stitch is loose. Tug both tails gently after the next couple of stitches.
- Puckered edge from carrying yarn. The carried strand is too tight. Leave a little slack every time you pick it up.
- The old color shows through. Dark colors behind light ones can show. Cut and use a bobbin instead of carrying, or carry inside the stitches.
Projects to practise on
A striped hat is the easiest place to start: try the striped beanie for joined-round color changes. For lots of small color changes, granny squares are ideal, since most of our granny square patterns change color every round. When you're ready for pictures, pick one of the C2C patterns.
Frequently asked questions
Do you change color on the last stitch or the next stitch?
On the last stitch in the old color. Work it until two loops are left (for single crochet), then finish it with the new color. That keeps the line between colors clean.
Do I have to cut the yarn every time I change colors?
No. For narrow stripes, carry the unused yarn up the side of the work. For small motifs, carry it inside the stitches as in tapestry crochet. Cut it when you won't use that color again for a while.
How do I stop the jog when changing colors in the round?
Work in joined rounds and change color on the joining slip stitch. In a continuous spiral, working the first stitch of the new color as a slip stitch makes the step much smaller.
How long should the tail be when changing colors?
About 6 in (15 cm). That's long enough to thread onto a tapestry needle and weave in securely.
Learning a new stitch? The stitch library has 21 crochet stitches with symbol charts and practice swatches.
More crochet guides
- How to crochet C2C (corner to corner)
- How many granny squares do you need for a blanket?
- Crochet hat size chart
- The best yarn for amigurumi
- How to read a crochet graph
- How much to charge for crochet
- Quick Christmas crochet gift ideas
- Crochet abbreviations: US and UK chart
- Crochet blanket sizes chart
- How to make a magic ring
- How to crochet a bag
- C2C vs mini C2C vs tapestry crochet
- Knitting abbreviations chart
- Knitting needle size chart
- How to make a pom pom
- How to join granny squares