How to crochet C2C (corner to corner)
Corner to corner is the easiest way to crochet a picture. Once you can make one tile, you can make a whole blanket.
What is C2C crochet?
C2C (corner to corner) is a technique where you build a square or rectangle out of small blocks called tiles. Each tile is a chain-3 space plus 3 double crochet stitches. You start in one corner with a single tile and work in diagonal rows, adding one tile per row until you reach the widest point, then removing one tile per row until you finish in the opposite corner.
Because every tile is a separate block, C2C is perfect for pictures: each tile is one square on a graph, so you can turn almost any pixel design into a blanket. Browse our free C2C patterns to see what's possible.
What you need
- Yarn: worsted weight (#4) acrylic or cotton is the easiest to start with.
- Hook: 5 mm (H-8) for worsted yarn. Each tile will be about 0.75 in square.
- Scissors, a tapestry needle and stitch markers.
Not sure how much yarn to buy? The C2C blanket calculator gives you the number of tiles, rows and yards for any size.
Step 1: the first tile
- Chain 6.
- Double crochet (dc) in the 4th chain from the hook, then dc in the next 2 chains.
- That's your first tile: a ch-3 space on one side and 3 dc. This is row 1.
Step 2: increasing rows
Every row on the increasing side starts by making a new tile, then adds one tile on top of each tile from the row before.
- Start a new tile: chain 6, dc in the 4th chain from the hook and in the next 2 chains.
- Attach it: turn the first tile so its ch-3 space is facing you, and slip stitch into that ch-3 space.
- Add a tile: chain 3, then work 3 dc into the same ch-3 space.
- Repeat "slip stitch into the next ch-3 space, ch 3, 3 dc" across the row. Each row has one more tile than the last.
Keep increasing until the diagonal edge is as wide as your blanket. For a square, that's when one row has as many tiles as the blanket has tiles across.
Step 3: decreasing rows
Once you reach the width you want, you start removing a tile at the beginning and end of each row.
- At the start of the row, don't chain 6. Instead, slip stitch across the 3 dc of the last tile and into its ch-3 space.
- Chain 3, 3 dc into that space, and continue across as usual.
- At the end of the row, stop after the last full tile; don't add a new one.
Repeat until a single tile is left in the far corner. Fasten off.
Making a rectangle
For a rectangle, increase until you reach the shorter side. Then keep the width the same on one side (decrease) while still increasing on the other side, until you reach the longer side. Finally decrease on both sides. Our calculator lists exactly when to switch.
Step 4: changing colours
For pictures, you change colour at the start of a tile. Work the last yarn-over of the previous tile with the new colour, then carry on. A few tips:
- Use bobbins. Wind a small amount of each colour onto a bobbin (or a clothes peg) so you're not dragging whole skeins around.
- Carry short distances, cut long ones. If a colour returns within 2–3 tiles, you can carry it inside the next tile. Otherwise cut it and weave in the end.
- Weave in ends as you go. A 40 × 40 picture can have hundreds of ends; doing them every few rows saves a miserable evening at the end.
Step 5: reading a C2C graph
A C2C graph is a grid where every square is one tile. Start in the bottom-right corner (bottom-left if you're left-handed). Row 1 is the single corner square; row 2 is the next diagonal of two squares, and so on.
Odd rows travel up and to the left on the graph, even rows travel down and to the right, because you turn your work at the end of every row. Written patterns save you counting: "Row 7: 3×A, 2×B, 2×A" means 3 tiles in colour A, 2 in B and 2 in A. Every one of our patterns includes these written rows. Read more in how to read a crochet graph.
Make your own C2C design
Once you've made a sample square, try a picture. You can turn a photo into a C2C graph, or draw your own square by square in the pattern designer, which gives you the colour key, yarn amounts and written rows automatically.
Frequently asked questions
Is C2C crochet good for beginners?
Yes. You only need chains, slip stitches and double crochet. Most people get the hang of it within the first 10 rows.
How big is one C2C tile?
About 0.75 in (2 cm) square with worsted yarn and a 5 mm hook. DK yarn makes tiles of about 0.6 in, bulky yarn about 1 in.
How many tiles do I need for a C2C blanket?
A throw of 50 × 60 in needs about 67 × 80 tiles in worsted yarn. Use the C2C blanket calculator for any size.
What's the difference between C2C and mini C2C?
Mini C2C uses half double crochet or single crochet tiles with a ch-1 space, so the tiles are smaller and the picture is more detailed.
Learning a new stitch? The stitch library has 21 crochet stitches with symbol charts and practice swatches.
More crochet guides
- How many granny squares do you need for a blanket?
- Crochet hat size chart
- The best yarn for amigurumi
- How to read a crochet graph
- How much to charge for crochet
- Quick Christmas crochet gift ideas
- Crochet abbreviations: US and UK chart
- Crochet blanket sizes chart
- How to make a magic ring
- How to change colors in crochet
- How to crochet a bag
- C2C vs mini C2C vs tapestry crochet
- Knitting abbreviations chart
- Knitting needle size chart
- How to make a pom pom
- How to join granny squares